Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Tarzana
Gate hinge replacement in Tarzana typically runs $280-$650 per hinge set, and custom on-site welding jobs start around $180 for crack repair and fabrication work. Most repairs are completed in one visit because we weld in your driveway instead of hauling the gate to a shop. If you’re south of Ventura Boulevard on a hillside property, there’s a fire-code layer to the work that most gate companies miss completely, and we’ll get into that below. Call us at (350) 247-4763 and a live person answers, day or night.
We work across Tarzana every week, from the flat streets north of Burbank Boulevard up through the winding drives south of Mulholland Drive. Long private driveways, steep grades, heavy ornamental iron, aging operators from the 1980s and 90s. We know the houses, we know the codes, and we know what fails on them.
Why Gatewood Fence & Gate Is Tarzana’s Preferred Gate Parts & Welding Company
Hal Gatewood started this shop in 2001, and his name is still on the door, the invoices, and the trucks that pull up to Tarzana homes. Our crew has welded gates on Melvin Avenue, rebuilt posts off Avenida Oriente, and replaced rollers on cantilever gates along Vanalden Avenue. We’re not a chain and we don’t route calls through a call center in another state. You call, one of us answers, and the person who shows up is the same person you talked to.
Every job carries our 90-Day Done Right Promise in writing. If something we fixed isn’t holding up, one call brings us back. No forms, no runaround. We also offer a free second opinion on any written estimate you’ve gotten from another company. Bring us their quote and we’ll tell you straight whether they’re selling you work you don’t need.
We’re certified to service nine major gate brands, including Viking, Ghost Controls, DoorKing, and Elite. We carry common parts on the truck so we’re not ordering a hinge or a control board and leaving your gate swinging loose while we wait on shipping. And if you’re in the hills where the fire code applies, we know exactly what LAFD wants to see on the override side.
Our Gate Parts & Welding Services in Tarzana
Hinge Replacement
Most sagging gates in Tarzana don’t sag in the middle. They sag at the hinge post, where years of weight and slope load have pulled the post out of plumb. We cut out the old hinge, weld in reinforced plates, and re-hang the panel so it swings true. On hillside estates south of Ventura Boulevard, we also check that the swing arc still lines up with the LAFD-required emergency override and the photocells, because a gate that won’t close fully is a bigger problem in the Very High Fire Hazard Severity Zone than it is on the flats.
Post Replacement
When a post leans, the gate will never hang right until the post’s problem is fixed. We saw out the old post, dig the footing deeper than the original install, set a new post, and weld the hinge plates in fresh. A typical post replacement in Tarzana runs $450-$900 depending on size and whether we’re dealing with steel or wood backing. On the steep drives off Reseda Boulevard, we regularly see posts that were set too shallow for the slope load from the start, so we embed them deeper than code minimums.
Rail Repair
Bottom rails on ornamental iron gates rust from the inside out, especially on older Tarzana estates where original gates are pushing 30 or 40 years. If a rail separates from the vertical pickets, the gate loses its structure and starts twisting. We replace the rail section, weld it solid, and grind the work so it blends with the existing iron. On wide driveway gates, we also check the cantilever and guide rollers while we’re under there, because a rail that’s been dragging often chews the rollers up too.
Custom Welding
Some jobs don’t fit a price-sheet line. Maybe your neighbor backed into a picket, or you’re adding a mid-rail to keep the dog in, or a rust-through section needs rebuilding. We do all of it on site with our own welding rig. Custom fabrication and crack repair in Tarzana typically runs $180-$500 per section depending on material and complexity. Hal’s rule is simple: fix what’s broken, don’t replace what isn’t. That’s the whole point of a welding shop.
All of this work falls under our Gate Parts & Welding service line, and we do every bit of it in your driveway, not in a shop forty minutes away.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Tarzana
We service and stock parts for the operators we see most often on Tarzana properties: Viking, Ghost Controls, DoorKing, and Elite. Hillside estates built in the 1980s and 90s often have original Linear, Elite, or Ramset units that are now failing at the control board or capacitor. We carry replacement boards, remotes, photocells, and receivers for all of them, and we know which units can be repaired versus which are past the point of sensible money. If you’re not sure what you have, show us a photo and we’ll tell you over the phone.
Common Gate Parts & Welding Problems We See in Tarzana Homes
- Undersized operators on steep-grade driveways. Gates installed during Tarzana’s 1980s-90s building boom were frequently fitted with operators that lacked the torque rating for the actual slope load. The motor burns out, someone replaces it with the same size, and it burns out again. The fix is upsizing the operator, not repeating the mistake.
- Santa Ana wind damage to cantilever slide gates. Exposed hillside properties get hit hard during fall wind events. A gust catches a wide gate panel, knocks it off the rollers, and bends the guide track. We realign the panel, weld the track brackets back square, and sometimes add mid-span rollers to distribute the load better.
- Heat-driven electronics failure. Tarzana routinely hits 100°F-108°F from July through September. Control boards and capacitors cook in that heat, especially inside dark metal operator boxes on south-facing driveways. We see a predictable spike in board failures every August, and the fix often includes adding ventilation to the housing.
- Rusted bottom rails and failed hinge welds on 1970s-1990s estates. Original ornamental iron gates on the larger Tarzana properties are aging all at once. Water gets inside the rail, rust works from the inside, and the welds at the hinge plates start popping. We cut out the rot and weld in new steel, then treat and repaint the seam.
The Tarzana Fire-Zone Reality Most Gate Companies Don’t Address
Here’s something that only applies to Tarzana and a few other hillside communities in the Santa Monica range: the properties south of Ventura Boulevard fall inside the City of Los Angeles’s Very High Fire Hazard Severity Zone. LAFD requires automated driveway gates on those properties to have approved emergency-access overrides, typically a Knox switch or equivalent, wired so fire crews can force the gate open from outside. That means every hinge replacement, post repair, or weld job on a hillside estate gate is also a fire-code compliance event. If the override doesn’t work after we’re done, the job isn’t done.
This isn’t a flatland Valley issue. On a track home north of the Boulevard, a gate repair is a mechanical fix. On a hillside property south of it, a gate repair that ignores the override can fail a fire inspection and put the home at risk during fire season. We wire the override, test it, and note it on the invoice. Hal has been doing this long enough that the LAFD inspection officers recognize the work.
One job off Reseda Boulevard sticks with us. A 16-foot ornamental iron swing gate had dropped so badly the latch wouldn’t engage. The hinge post had leaned under years of slope load, and the original 1/2 HP Linear operator was straining just to move the panel. We removed the old post, poured a new footing with deeper embedment, welded reinforced hinge plates, and upsized to a high-torque Viking operator rated for the incline. A fresh Knox switch went in alongside it, wired and tested. The gate swings, the latch catches, and the fire department can get in if they ever need to.
Pricing for Gate Parts & Welding in Tarzana, CA
Here’s what you can expect to pay in Tarzana for the work we do most often. Hinge replacement runs $280-$650 per hinge set. Post replacement runs $450-$900 per post depending on material, size, and whether concrete work is involved. Rail repair ranges $180-$450 per section. Custom welding and crack repair starts at $180. Operator upsizing or replacement runs $600-$1,800 installed depending on brand, torque rating, and whether new wiring or safety edges are needed. We quote every job in writing before any work starts, and the price we quote is the price you pay. No trip charge inside the county. We take $40 off any repair over $200, and we hold a permanent 10% discount for seniors and veterans. Call (350) 247-4763 for a free estimate.
We Also Serve Cities Near Tarzana
Our trucks cover the whole west Valley. If you’re just over the line in Encino, Reseda, Sherman Oaks, or Northridge, we’re close by and we know those streets the same way we know Tarzana. Whether you’re in the hills or on the flats, the same crew and the same 90-Day Done Right Promise apply. That’s the whole business model: the name on the shop is on everything we do, wherever we do it. You can learn more about our local work on the Gate Parts & Welding in Tarzana page or call (350) 247-4763.
Serving Tarzana, CA - Our Local Coverage Area
We’re based in the Tarzana area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Tarzana
Because the operator was probably undersized from the start. On steep-grade driveways south of Ventura Boulevard, gates installed in the 1980s and 90s often got 1/2 HP operators that were never rated for the slope load. The motor works twice as hard as it should, the capacitor cooks in Tarzana’s summer heat, and the board follows it. Replacing the motor with the same size just restarts the clock on the same failure. The fix is a torque-matched operator sized for your driveway’s actual grade. Call (350) 247-4763 and we’ll check the incline and spec the right unit.
Post replacement and welding on an existing gate typically don’t require a standalone permit, but if your property is in the Very High Fire Hazard Severity Zone, your gate must maintain its LAFD-approved emergency-access override at all times. That’s not optional, and it’s the part most gate contractors forget. We work with the existing override, restore it, and if it fails, we tell you before we leave. For full gate installations or reconfigurations, we’ll advise whether LAFD review is needed. Call us for a straight answer on your specific property.
Usually a combination of welding and alignment work. Wind loads push the gate panel laterally, the rollers walk off the track, and the guide brackets bend. We weld the brackets back square, realign the cantilever wheels, and in many cases add mid-span rollers to split the wind load across more contact points. On exposed Tarzana hillsides, we also recommend upgrading worn wheel assemblies before they chew up the bottom rail. That saves you from a much bigger rail rebuild later. Call (350) 247-4763 for an on-site look.
Yes, and that’s the job we do most often. A gate that has “sagged” almost always has a problem at the hinge post, not in the middle of the panel. The post has leaned, the hinge welds have cracked, or the hinge bearings are shot. We pull the panel, reset or replace the post, weld new reinforced hinge plates, and rehang the gate. Unless the panel itself is rusted through, it doesn’t get replaced. Fix the panel without the post and you’ll fix it twice. We’d rather do it once.
Tarzana routinely hits 100°F to 108°F between July and September, and the San Fernando Valley traps that heat hard. Capacitors on gate operators fail first, especially inside dark metal housings on south-facing driveways. Control boards are usually next, followed by receiver and remote failures as the solder joints thermal-cycle. Once a unit overheats and blows a capacitor, the board often gets damaged in the process. It’s why we see an August repair spike every year. If you’re in that cycle, call (350) 247-4763 and we’ll test the unit and tell you what actually needs replacing.
Call Gatewood Fence & Gate for Gate Parts & Welding in Tarzana
If your gate is sagging, jammed, burned out, or the Santa Anas just rearranged your cantilever rollers, call (350) 247-4763. A live person answers, any hour. We’ll talk through what you’re seeing, give you a straight price, and schedule a time that works. Free estimates, no trip charge inside the county, and every job is backed by our 90-Day Done Right Promise in writing. Hal Gatewood’s name is on the shop and on every invoice we hand out in Tarzana. That’s the kind of accountability that’s been working since 2001.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Tarzana since 2001.