Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Granada Hills
Gate parts and welding in Granada Hills usually comes down to one decision: fix what you have or replace it. Most of the time, the smarter money is on repairing. A new hinge bracket welded onto a solid post costs a fraction of a full gate replacement, and a properly rebuilt gate from 1995 will outlast a big-box gate from 2025. If you live off Balboa, Rinaldi, or anywhere near Knollwood, call (350) 247-4763 and we’ll come look at the gate before you spend a dime on parts you might not need.
Hal Gatewood has been doing this since 2001. The name is on the shop, the license number is published, and the person who answers the phone at 2 a.m. isn’t a script. We repair what other companies want to replace, and we do the welding right there in your driveway instead of hauling your gate off to some shop across the Valley.
Why Gatewood Fence & Gate Is Granada Hills’s Preferred Gate Parts & Welding Company
Granada Hills is a specific kind of place. The housing stock is older, the lots are bigger, and the gates were mostly hung between 1992 and 1998. We know those gates because we’ve worked on hundreds of them. A ranch house near Knollwood has a different gate problem than a cul-de-sac off Zelzah, and after years of calls in this zip code, we can usually diagnose the issue on the phone before we even roll up.
Every job we do in Granada Hills carries the 90-Day Done Right Promise in writing. If it’s not right, one call brings us back. No runaround, no dispatcher asking for a case number. Just Hal or one of his crew showing up to make it right. Granada Hills homeowners tend to be the practical type. They don’t want a sales pitch. They want somebody who’ll tell them the truth: sometimes a $90 hinge beats a $900 gate operator swap, and we’ll tell you exactly that.
Our Gate Parts & Welding team keeps common hinge sets, rollers, latch kits, and weld stock on the trucks, so most repair calls in Granada Hills are done in one trip. The scheduling and dispatch are coordinated from our Los Angeles office, but the work in Granada Hills is done locally, by local hands.
Our Gate Parts & Welding Services in Granada Hills
Post Replacement
Post replacement is the repair most Granada Hills gates actually need. The 1994 Northridge quake shifted footings all over this corner of the Valley, and a post that settled three degrees off-vertical can’t hold a gate properly no matter how many times you adjust the hinges. We cut the old post out, dig down to the footing, set new steel with rebar, and weld the post plumb. Then the gate hangs true for decades, not seasons.
Hinge Replacement
Hinges in Granada Hills take a beating from Santa Ana wind gusts funneling through the Santa Susana Pass corridor. A swing gate blown repeatedly past its travel stops bends hinge brackets slowly, over months, until the gate starts dragging on the ground or binding at the latch post. We replace hinge sets with heavier brackets than what came off, because the wind here isn’t going away.
Rail Repair
Sagging rails on slide gates are usually a symptom of a failed roller or a bent track, not a bad rail itself. That said, after enough seasons of 105-degree afternoons and wind-blown debris, steel rails do fatigue. We weld in replacement rail sections or straighten and reinforce what’s there, judged case by case. The goal is to fix the rail without hiding what caused the failure.
Custom Welding
Some gates in Granada Hills are old enough that parts simply aren’t manufactured anymore. That’s where on-site welding earns its keep. We fabricate replacement hinges, reinforce rack mounts, weld cracked weldments, and build custom latch brackets to match the original design. No hauling, no week-long wait at a fabrication shop. Hal fixes it in your driveway, the way it should be.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Granada Hills
We’re certified to service nine major gate brands, and in Granada Hills we most often work on LiftMaster, FAAC, DoorKing, Viking, and Ghost Controls operators. The specific failure modes change by brand and by year. A 1996 FAAC swing arm on a Zelzah Avenue gate fails differently than a 2004 Viking slide operator near Rinaldi. We stock common control boards, capacitors, remote receivers, and safety photo-eyes on the trucks, so when we diagnose a bad Ghost Controls board on a Monday, we’re not waiting until Thursday for a part to ship.
Common Gate Parts & Welding Problems We See in Granada Hills Homes
- Summer binding on swing gates. Metal expands in heat. A gate that closes perfectly in January can bind hard in August, and Granada Hills regularly pushes past 105°F. That’s rarely an operator problem. It’s a post that’s a few degrees out of plumb from 1994 settling, and it’s the first thing we check with a level.
- Control boards cooked by Valley heat. The inland heat here thermal-cycles capacitors and circuit boards years before the manufacturer’s rating. A dead LiftMaster or FAAC board on a west-facing gate on a Granada Hills lot with no shade is one of the most common calls we run in July and August.
- Wind-blown gates stripping gears. Santa Ana gusts channel straight through the Santa Susana Pass and hit swing gates broadside, blowing them past their travel stops. Repeatedly. That bends hinges and strips the rack-and-pinion gears on slide gates.
- Corroded hinge welds on older steel gates. The original welds on 1990s-era gates are starting to fatigue and rust where foot traffic, sprinkler overspray, and decades of heat cycles meet. We cut out the old welds and re-weld with full-penetration brackets so the repair outlasts the original work.
Pricing for Gate Parts & Welding in Granada Hills, CA
Gate parts and welding pricing in Granada Hills follows the work, not the guesswork. A standard hinge replacement runs $165 to $340 per hinge set, depending on gate weight and whether we need to weld new brackets to the post and panel. Post replacement, including cutting out the old steel, new footing with rebar, and setting the post plumb, typically runs $480 to $850 per post. Custom welding work like fixing a cracked weldment or fabricating a replacement bracket is billed at $95 to $145 per hour plus materials, and most custom jobs on a single gate finish in two to four hours. Rail or roller repairs on slide gates run $220 to $460, depending on whether the rail itself needs sectioning. You’ll get the price before we start, in writing, and it’s the price you’ll pay. No changes at the door. And if you’ve got a written estimate from another company, bring it in for a free second opinion. If you’re over 65 or a veteran, take 10 percent off any of these numbers. Call (350) 247-4763 for an exact quote, free.
We Also Serve Cities Near Granada Hills
We run calls all over this stretch of the San Fernando Valley. If you’re in San Fernando, Northridge, Sylmar, or Panorama City, the same on-site welding and repair-first approach applies. We’re part of Granada Hills because we work here every week, not because we bought ad space in a local directory.
Serving Granada Hills, CA - Our Local Coverage Area
We’re based in the Granada Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Granada Hills
Your gate post is slightly out of plumb, almost certainly from seismic settling during or after the 1994 Northridge quake. Steel expands in heat, so a post that’s off-vertical by two or three degrees won’t cause binding in cool weather, but when the Valley hits 100+ degrees, the metal swells just enough to make the gate stick. We check the post with a level before touching the operator, because replacing the operator won’t fix a structural misalignment. Call (350) 247-4763 for a free look at your post alignment.
Yes, in most cases. Retrofit photocell kits and safety-edge transmitters are available for most brands from that era, and we carry retrofit kits for LiftMaster, FAAC, DoorKing, Ghost Controls, and Viking operators on our trucks. The limiting factor is whether the original control board has an input terminal that can accept a modern photocell signal. If it doesn’t, we can usually wire in a standalone safety relay without replacing the whole operator. That’s a $280 to $420 fix versus $1,900 to $3,400 for a full operator replacement in Granada Hills. Call for an exact assessment.
It’s almost always a hinge post problem. Wrought iron and tubular steel panels don’t sag on their own. They sag because the hinge post is leaning or the hinges themselves have worn bushings and sloppy pivot points. The panel is just along for the ride. In Granada Hills, the usual culprit is a post that settled during the 1994 quake and has been slowly leaning for three decades. Fix the post and the hinges, and the panel straightens back out. Skip the post and you’ll fix that gate twice.
We carry and service parts for LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That covers nearly every residential operator installed in Granada Hills since the 1990s. We stock common control boards, capacitors, remote receivers, and photocell kits for DoorKing, Viking, Ghost Controls, and Elite specifically, because those are the brands we see most often on older Valley ranch homes. If we don’t have the part on the truck, we typically have it within one business day.
Because the wind is pushing the gate slightly sideways while it runs, causing the drive pinion to climb the rack for a split second. It’s not a sign your operator is dying. It’s a sign the gate is getting blown off its track line, and the fix is usually adjusting the guide rollers or shimming the rack so the pinion stays engaged under lateral load. We see this all over Granada Hills because of the Santa Susana Pass wind corridor. Call (350) 247-4763 and we’ll adjust it before the next wind event does real damage.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Granada Hills and the surrounding San Fernando Valley since 2001.