FAAC Gate Repair Nationwide | Gatewood Fence & Gate

FAAC Gate Repair in Encino: What to Know First

FAAC gate repair in Encino is what we handle most weeks, and most jobs are done the same day we show up. A typical FAAC hydraulic operator repair runs $385 to $750 depending on the model and what failed, and we quote the full price before any work starts, not after. If your FAAC gate is stuck, sluggish, or making noise, call (350) 247-4763 and Hal Gatewood will walk you through what he thinks is wrong before he even gets in the truck.

Call (350) 247-4763

We’re an independent FAAC service provider. We don’t claim to be a factory shop, but we’ve been inside enough FAAC operators in Encino to know their habits: which seals leak, which boards cook themselves, and which models are worth saving versus swapping. This page is for homeowners with a FAAC gate that used to work right and doesn’t anymore.

How FAAC Products Fail - and How We Fix Them

FAAC builds good operators, but everything mechanical eventually shows its age. Around Encino, with the heat and the valley dust, we see the same failure patterns repeat. Here are the five we fix most.

• FAAC 750 and 760 (barrier arms): The hydraulic fluid gets contaminated and the arm rises halfway, stutters, and reverses. Most shops say “new motor.” We flush the system, replace the o-rings, and the arm runs smooth again for a third of the money.
• FAAC 400 series (swing gates): The leaf starts creeping open on its own about an inch every few minutes. That’s a failing lock solenoid in the operator, not a structural problem. We confirm with a pressure gauge test, then replace the solenoid and re-bleed the system.
• FAAC S418 and similar (sliding gates): The gate shudders and trips the safety sensor mid-travel. We see the rack gear wearing unevenly because the original installer never shimmed it level. We re-shim, realign the rack, and the shudder goes away without replacing the motor.
• FAAC photocell faults: The gate closes on the driveway sensor intermittently, or refuses to close at all. The problem in Encino is usually dust film baked onto the lens by the sun. Clean and realign first, replace only if the beam stays weak. That’s a $20 fix disguised as a $300 parts bill elsewhere.
• FAAC E024U control board: The operator goes completely dead after a hot week. The board’s capacitor set swells and the relay contacts arc. We replace the board with a genuine FAAC or a quality-rated aftermarket equivalent, and we seal the cabinet properly so the next one lasts longer than the first.

Our FAAC Gate Repair Process

If you call us about a FAAC gate, here’s exactly how the job goes from start to finish.

1. 1
   You call (350) 247-4763. A live person answers, not a voicemail. Hal asks what the gate is doing, what model is on the label, and whether it’s stuck open, stuck closed, or somewhere in between. That tells us which parts to bring.
2. 2
   We show up on the day we promised. We check the operator, the hinges, the track or arm, and the safety sensors. We look at how the whole assembly is mounted, because half of FAAC failures in Encino are installation problems, not parts problems.
3. 3
   We quote the fix before we touch it. Every job gets a written price: parts, labor, the whole thing, agreed before we start. You’ll never get surprised at the door.
4. 4
   We use the right parts. When a genuine FAAC part is available at a sane price, we use it. When aftermarket makes more sense, we tell you why and what the difference is. No mystery parts, no upselling what you don’t need.
5. 5
   We test the gate through at least ten full cycles. Open, close, reverse, safety sensor, manual release. If it doesn’t run right, we don’t leave.
6. 6
   You get the 90-Day Done Right Promise in writing. If anything we fixed fails within 90 days, one call brings us back. No runaround, no fine print.

What FAAC Gate Repair Costs in Encino

Here’s what we actually see on FAAC jobs around Encino. These are honest ranges, not a menu we’re going to pad.

• Hydraulic fluid flush and seal replacement: $240 to $340
• Lock solenoid replacement: $180 to $260
• Control board replacement (FAAC E024U or similar): $380 to $550 with the part
• Photocell replacement and realignment: $120 to $185
• Rack gear shim and realignment: $200 to $300
• Complete FAAC operator replacement: $1,100 to $2,400 installed, depending on the model and gate size

What moves the price: gate weight, access height, and whether the operator was installed right the first time. A FAAC that was thrown in by a handyman usually takes more labor to correct. Every estimate is free, no trip charge inside the county, and we quote before we touch anything. Call (350) 247-4763 for an exact number on your gate.

Why Encino Homeowners Call Gatewood Fence & Gate for FAAC Work

We’ve been fixing gates in the San Fernando Valley since 2001, and a big part of that has been FAAC operators in Encino, Sherman Oaks, and Tarzana. Hal Gatewood grew up two blocks from Balboa Park and took welding and fabrication courses at Los Angeles Pierce College over in Woodland Hills, so when a hinge post is leaning or a bracket snapped, he welds it on site in your driveway instead of hauling the gate off or telling you to buy a new one. The name is on the shop, and the shop is down the road, that’s the oldest accountability there is.

We’re not a FAAC-only shop. That’s an advantage for you because when a FAAC board fails and the part is a week out, we know exactly what fits from LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, and we can give you options that get your gate working now, not next month. Every job carries the 90-Day Done Right Promise, in writing.

FAQs