Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Access Control in Encino: What to Know First
FAAC gate access control repair in Encino typically runs $225-$480 for keypad and receiver issues, and we complete most FAAC jobs the same day we diagnose them. We’re an independent FAAC service provider, which means we fix what’s broken instead of telling you to replace the whole operator, and we quote the price before any work starts.
If you own a FAAC gate in Encino and the keypad stopped talking to the board, or the remote quit after a power blink, or the phone entry system rings but won’t release the latch, this page is for you. Call (350) 247-4763 and Hal Gatewood or one of his crew will pick up. You’ll get a straight answer about whether it’s a $40 board fuse or a $400 board replacement.
How FAAC Products Fail - and How We Fix Them
FAAC builds solid operators, but every brand has its ways of going bad, especially in Encino’s dry heat and occasional Santa Ana dust storms. Here’s what we actually find when we open the box:
- FAAC 412 and 415 operators losing programming after a power surge. The E024S control board on these older swing-arm models has a memory chip that’s sensitive to voltage spikes. The symptom is a keypad that lights up but won’t accept the code, or a remote that worked yesterday and does nothing today. We re-flash the board if it’s recoverable, or swap in a replacement board and re-program all your codes on site. This is the single most common FAAC access control call we get in Encino.
- Photon and photocell misalignment on FAAC swing gates. The FAAC 424 and 415 series rely on a photocell pair at the gate edge. In Encino, landscaping crews bump these sensors with trimmers, or the posts shift slightly in clay soil after rain. The gate will close but refuse to reopen on command, or it reverses mid-cycle. We realign the photocells, replace broken housings, and re-test the safety loop before we leave.
- Entry keypads corroding internally on FAAC 412 Compact and sliding gate models. The factory keypads aren’t sealed well against morning fog that rolls in off the Sepulveda Basin. We open them and find green corrosion across the ribbon connector. Sometimes we can clean and reseal the board; sometimes the keypad needs replacing. When we replace, we use a sealed aftermarket keypad that costs less than the FAAC-branded version and lasts longer in Encino’s damp mornings.
- Intermittent remote range on FAAC 750 and 844 slide operators. If your remote only works when you’re ten feet away, the receiver antenna is often the problem. On slide gate models mounted low to the ground, the antenna wire gets pinched or snapped by landscaping fabric. We solder on a new antenna, or add a small inline signal booster if your driveway is long. The fix is usually under an hour.
- Gate opens but won’t fully latch, or close limit keeps drifting on FAAC slide operators. Encino’s temperature swings from cold nights to hot afternoons make limit switch contacts expand and contract. The gate will open fine but stop six inches short, leaving the latch misaligned. This isn’t a board failure, it’s mechanical drift. We set limits, tighten the cam screws, and lubricate the chain with a dry lubricant that holds up in dust.
Our FAAC Gate Access Control Process
Here’s what happens when you call us for a FAAC access control issue in Encino:
- 1
You call, a person answers. No voicemail, no menu tree. Hal or his crew asks what the gate is doing, what model you have if you know it, and when you’re available.
- 2
We show up in the window we promised. We bring parts for every FAAC series we service, plus the diagnostic tools to read fault codes off the board.
- 3
We diagnose in place. We don’t haul your operator to a bench unless it’s truly dead. Most FAAC access control problems are diagnosed in the driveway in under 45 minutes.
- 4
We tell you the fix and the price before we touch a part. OEM FAAC board vs. quality aftermarket sensor, new keypad vs. re-flash, we lay out the real options and the real cost difference.
- 5
We repair, test, and clean up. We run the gate through full cycles, check safety edges and photocells, and leave your driveway cleaner than we found it.
- 6
We hand you the 90-Day Done Right Promise in writing. If the fix doesn’t hold, one call brings Hal back. No runaround, no arguing your warranty status.
What FAAC Gate Access Control Costs in Encino
Here are honest dollar ranges for the FAAC work we do most often in Encino:
- Keypad replacement (aftermarket sealed unit): $185-$265 installed, depending on whether we need to run new wire.
- Control board replacement (FAAC 412/415 E024S): $300-$480 installed, including reprogramming your existing remotes and keypad codes.
- Receiver or antenna repair: $95-$180, depending on whether the receiver module needs replacing or just soldering.
- Photocell replacement and realignment: $140-$220 per pair, including new housings if they’re cracked.
- Full access control upgrade (keypad plus phone entry or video intercom): $850-$1,800, depending on whether we’re wiring into an existing FAAC board or adding a separate controller.
What moves the price most is whether the operator is old enough that FAAC discontinued the control board. If we have to adapt a newer board to an older swing arm, that’s more labor. But we’ll tell you that before we start, not after. Call (350) 247-4763 for an exact quote - estimates are free, and there’s no trip charge inside the county.
Why Encino Homeowners Call Gatewood Fence & Gate for FAAC Work
Hal Gatewood has been fixing gates in the San Fernando Valley since 2001, and most of that time has been right here in Encino. He grew up two blocks from Balboa Park and took welding and fabrication courses at Pierce College over in Woodland Hills, which is why he treats a FAAC access control problem as part of the whole gate, not as an isolated board swap. If the hinge is binding and making the operator work twice as hard, he’ll find it and tell you.
We’re not a FAAC dealer pushing a new unit. We’re the independent shop that tells you which parts are worth buying OEM and which ones are better as quality aftermarket. Need a second opinion on a written estimate from another company? Bring it in, and we’ll look at it free. And if your FAAC system is truly beyond saving, we’ll tell you straight and show you what replacing it with a FAAC, LiftMaster, Mighty Mule, Ghost Controls, or DoorKing system would actually cost.
FAQs
We’re an independent FAAC service provider, so we don’t perform warranty work on FAAC’s behalf. But if your FAAC is still under warranty, we can diagnose the problem and tell you exactly what the manufacturer needs to see to process your claim. Some Encino customers prefer to pay us to fix it same-day rather than wait for a manufacturer service appointment.
Most FAAC access control calls in Encino are same-day or next-day, especially if your gate is stuck open or stuck closed. We answer the phone live 24/7, so you’ll know your window before you hang up. If it’s a board failure we don’t have in stock, we can usually have it in hand within two business days.
Both, and we tell you which one makes sense before we do anything. For control boards and logic components, we use genuine FAAC parts when they’re still available, because programming compatibility matters. For things like keypads, photocells, and antennas, we often recommend a sealed aftermarket part that holds up better in Encino’s weather and costs less. You always get the choice.
On FAAC 412 and 415 swing operators, intermittent keypad behavior is usually a corroded ribbon connector inside the keypad housing, not the board. We can usually tell within five minutes by opening the keypad. If the board responds when we jump the input directly, the keypad is the problem. Call (350) 247-4763 and we’ll check it while you watch.
Yes. Most FAAC operators have an open input on the control board that accepts a phone entry or video intercom trigger. We wire the new device into that input and program the relay timing so the gate holds open long enough for a delivery truck or a guest. It’s a same-day job in most cases.
Written by Hal Gatewood, Owner, Gatewood Fence & Gate at Gatewood Fence & Gate, serving Encino and nearby areas.