FAAC Gate Parts & Welding Nationwide | Gatewood Fence & Gate

FAAC Gate Parts & Welding in Encino: What to Know First

We’re an independent FAAC service provider in Encino, and we stock or can source the gate parts most FAAC owners need within one to three business days: hinges, posts, rails, rollers, latches, locks, and custom-welded repairs done right in your driveway. Most FAAC gate parts and welding jobs run between $350 and $1,400, and we quote the price before any work starts, so you’ll never get a surprise invoice at the door. If you own a FAAC gate in Encino and it’s sagging, sticking, or making a sound it shouldn’t, call (350) 247-4763 and Hal Gatewood or his crew will take a look.

Call (350) 247-4763

Key Takeaways:

• Independent FAAC service, not factory-authorized: we fix what’s worn, not what’s convenient.
• On-site welding: the gate stays in your driveway, so you can watch the work if you want.
• Upfront pricing, free estimates, 90-Day Done Right Promise in writing.
• Serving Encino and the San Fernando Valley since 2001, with a live person answering 24/7.

How FAAC Products Fail - and How We Fix Them

FAAC builds quality operators, but the gate itself, the hinges, the posts, and the rails, those take the daily beating. Here’s what we actually see on FAAC gates in Encino, and how we’d repair each one.

• FAAC 770 and 391 series: hinge post fatigue. FAAC operators open and close with real authority, and over years of that torque, the hinge post works loose in the soil, especially in Encino’s clay-heavy ground. The gate sags, the operator strains, and eventually the chain skips or the arm binds. We weld a new post base, reset the post in concrete, then wire-brush and weld the hinge brackets back to square. The panel gets fixed, and the ground the post stands in gets fixed too.
• FAAC S418 and S450 hydraulic operators: slow creep at the piston. These are tough units, but when the hydraulic seals wear, the gate drifts open or closed by itself. Homeowners assume the operator is dead and call for a replacement. Most of the time, the operator mount plate has cracked along its weld at the bracket, leaking fluid. We remount and reweld the plate on site, then rebleed the system. That saves you a thousand-dollar operator swap.
• FAAC 400 and 402 gate openers on chain drives: chain pull and rail wear. The chain stretches over time, the rail guide wears where the carriage rides, and you hear a grinding or a slap when the gate moves. The fix is often a new roller set, a welded reinforcement plate on the rail, and tensioning the chain, not a whole new operator. We carry aftermarket chain lengths that match FAAC pitch specs and cut them to fit.
• FAAC 844 and 415 LS on swing gates: hinge bearing failure. The grease in those zinc pivot bearings dries out, the bearing galling starts, and the gate binds. We pull the gate, press in new bearings, and weld a grease zerk into the hinge housing so it can be lubricated without taking the gate down again. That’s a small modification FAAC doesn’t include from the factory, and it pays back every year.
• FAAC C720 and C721 barrier arms: weld failure at the arm cradle. The barrier arm sits in an aluminum cradle that’s bolted on, and after a few years of wind shear off the hills, the bolts elongate and the cradle cracks. We weld a steel insert into the cradle pocket and replace the bolts with grade-8 hardware. It fixes the rattle and keeps the arm from sagging into traffic.

Our FAAC Gate Parts & Welding Process

When you call (350) 247-4763 about a FAAC gate in Encino, here’s how a typical job plays out. It’s a simple process, because we do the work in your driveway, and you can watch every step.

1. 1
   You call, a live person answers. We ask what the gate is doing, what kind of FAAC unit it is, and when it started acting up. We schedule a time that same day or the next morning in Encino, no trip charge.
2. 2
   Hal or one of the crew shows up and looks. We inspect the gate, the operator, the posts, the hinges, and the rails. We tell you what’s actually wrong, not what we’d like to sell you.
3. 3
   We give you a firm price. We tell you what parts need to be replaced, whether we recommend OEM FAAC parts or a quality aftermarket equivalent, and what the welding work will cost. You approve the number before we touch a tool.
4. 4
   We do the work on site. Parts get swapped, welds get laid down, the gate gets squared and rebalanced. We don’t haul your gate away to a shop across town.
5. 5
   We test the gate through full open and close cycles, check safety edges and reversing behavior, and make sure the operator isn’t straining. We clean up the weld spatter and the metal shavings before we leave.
6. 6
   You get the 90-Day Done Right Promise in writing. If something’s not right, call us and we come back and make it right. That’s the whole job.

What FAAC Gate Parts & Welding Costs in Encino

Here’s what we typically bill for common FAAC gate parts and welding jobs in Encino. These are real numbers, not phone quotes that change when the truck pulls up.

• Hinge replacement (one hinge, welded in place): $280-$520
• Post reset and weld (dig, concrete, re-level, weld brackets): $550-$950
• Rail repair and roller replacement: $300-$650
• Custom welding (cracked frame, bracket, cradle): $150-$400 per weld point
• Latch and lock replacement (FAAC-compatible strike and weld): $180-$350
• Full gate repair with multiple welds and parts: $750-$1,400

What moves the price: how deep the post is set, whether the gate is steel or aluminum, how many weld points are cracked, and whether FAAC OEM parts are required to keep a warranty intact. We’ll tell you if aftermarket makes sense, and we’ll tell you if it doesn’t. Call (350) 247-4763 for a free estimate, we don’t charge a trip fee anywhere in Encino.

Why Encino Homeowners Call Gatewood Fence & Gate for FAAC Work

Hal Gatewood has been fixing gates in the San Fernando Valley since 2001, and he grew up two blocks from Balboa Park, so he knows Encino’s soil, traffic, and weather like the back of his hand. His name is on the shop, his address is published, and if he tells you he’ll be there Tuesday at nine, he’ll be there Tuesday at nine. We weld on site, so the gate never leaves your property. We back every job with the 90-Day Done Right Promise, not “up to” or “in most cases,” in writing. And when a FAAC part is discontinued or backordered, we can usually adapt the job around it, since we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing systems across Encino. One call, (350) 247-4763, and a live person answers. Not a voicemail. Not a call center in another state. Us.

FAQs