Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across Reseda
Gate parts and welding in Reseda is a different job than it is almost anywhere else in the Valley. The 1994 Northridge earthquake cracked and shifted concrete footings under thousands of gate posts across this neighborhood, and three decades of settling since have left iron swing gates and slide gates chronically out of plumb. That means a hinge that fails on a house off Saticoy is usually not just a hinge problem. It is a footing problem wearing a hinge disguise. If you need a Gate Parts & Welding job done right in Reseda, call Hal at (350) 247-4763 and he will tell you straight what is actually wrong before anyone touches a wrench.
Why Gatewood Fence & Gate Is Reseda’s Preferred Gate Parts & Welding Company
Hal Gatewood has been running this shop since 2001, which means he was here through the years when half the neighborhood was still arguing with insurance adjusters about earthquake damage. His name is on the building, his address is published, and his cell number is not a secret. When a Reseda homeowner calls about a gate that will not close or a hinge that sheared off, the person who shows up is someone who has welded gates on Lindley Avenue, on Arminta Street, on Sherman Way. Not a subcontractor reading a script.
Every job carries the 90-Day Done Right Promise, written on the invoice, not implied. If the fix does not hold, Hal comes back. That matters more in Reseda than most places, because so many gate failures here trace back to the earthquake. “Fix the panel without the post and you will fix it twice” is not a slogan for us. It is the job description. Reseda customers call us because the first company replaced a hinge and six months later the gate sagged again. We find the footing crack the first company never looked for.
Our Gate Parts & Welding Services in Reseda
Hinge Replacement
Hinge replacement in Reseda needs to account for what happened to the post in 1994. We carry heavy-duty barrel hinges, weld-on pillow block bearings, and adjustable weld-on hinges that let us correct for a post that is a quarter-inch out of plumb. On a 1960s ranch house near Reseda High, the original ornamental iron hinges are often rusted through at the pin. We cut the old hinge off, grind the post clean, and weld a new one on site. The gate stays in your driveway. You do not haul it anywhere.
Post Replacement
This is the service that fixes what other companies miss. A steel post set in a cracked footing from the Northridge quake will still rock, even if the gate is perfectly balanced. We break out the old concrete, set a new Schedule 40 steel post with a deeper embedment, and pour fresh concrete around it. Then we weld the hinge brackets to the new post, not bolt them. In Reseda, where half the posts are 50 to 70 years old and sitting on pre-1994 concrete, post replacement is the repair that actually lasts. A plated or sleeved post is a band-aid we will not sell you.
Rail Repair
Steel gate frames expand in Reseda heat. A 12-foot iron gate on a 105-degree August afternoon can grow enough to bind against its own stop bolts. Over time that flexing cracks the rail welds and bows the top rail. We straighten, weld, and reinforce the rail, and we check the operator’s limit switches while we are there. Because the motor that has been pushing against binding steel all summer is a motor that is about to burn out. Fixing the rail without checking the operator is how you end up with a gate that looks right and stops working in October.
Custom Welding
Some gates in Reseda cannot be bought off a shelf. Side-yard driveway gates on 1950s tract homes were built to fit odd openings, and when a section of ornamental iron scrollwork breaks off, nobody stocks a replacement. Hal welds on site. He can fabricate a matching section, patch a rusted-through stile, build a Gate Installation - Reseda custom gate from scratch, or add a pedestrian pass-through to an existing driveway gate. We weld steel, iron, and aluminum, and we finish the work so it does not look like a patch. It looks like it was always there.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Reseda
We service and stock parts for Reseda Gate Motor & Opener systems from most major manufacturers, including FAAC, BFT, Linear, and Viking. If your opener is older, we can usually match it. Reseda has a lot of apartment buildings along Sherman Way and Reseda Boulevard running aging FAAC and Viking operators from the 1990s, and we keep common boards, limit switches, and gear kits available so we are not telling a property manager to wait two weeks for a part. Same applies to homeowners. If we have to order something, we tell you on the spot and give you the real timeline. No surprises.
Common Gate Parts & Welding Problems We See in Reseda Homes
- Rocking hinge posts from post-1994 footing cracks. The post shifts, the gate sags, the hinge pin shears, and the homeowner replaces the hinge again and again. The footing is the problem. We repour it, embed the post deeper, and the gate stops sagging.
- Heat-bound steel frames cooking opener motors. Reseda gets some of the hottest July and August temperatures in LA County. Metal expands, binds against the stop bolts, and the motor strains until the limit switch or the board fails. You hear the motor laboring on hot afternoons. That sound is a warning.
- Santa Ana wind damage to aluminum and old iron gates. Fall winds hit the interior Valley hard. Lightweight aluminum gates rack and bend. Old iron gates with rusted hinge brackets snap clean off. A post-anchor check and a heavy-gauge hinge upgrade can prevent most of it.
- Rusted-through rails and stiles on 50-to-70-year-old gates. Original ornamental iron from the 1950s through 1970s is often rusted from the inside out. A gate that looks solid will have paper-thin metal hidden behind the paint. We find it, cut it out, and weld in new steel.
Pricing for Gate Parts & Welding in Reseda, CA
Here are real numbers for Reseda. A single hinge replacement typically runs $120 to $180 per hinge, including the part and the welding. A full hinge set on a heavy driveway gate, with grinding and weld-on replacement, runs $350 to $550. Post replacement with breaking out the old footing, setting a new steel post, and pouring fresh concrete runs $400 to $800 per post, depending on depth and access. Custom welding starts around $100 for a small repair and ranges up to $1,200 or more for a full custom gate build. Every quote is agreed before we start. No one changes the number at the door. And the 90-Day Done Right Promise applies to the whole job. We also offer $40 off any repair over $200, no trip charge inside the county, and a permanent 10% discount for seniors and veterans. Call (350) 247-4763 and we will give you a straight price.
We Also Serve Cities Near Reseda
We run calls to Gate Parts & Welding in Reseda every week, and the same crew covers Tarzana, Northridge, Encino, and Panorama City. If you are in one of those neighborhoods, the number is the same and the promise is too.
Serving Reseda, CA - Our Local Coverage Area
We’re based in the Reseda area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Reseda
Your hinge post is almost certainly rocking in a cracked concrete footing from the 1994 Northridge earthquake. The gate sags because the post moves, not because the hinge is bad. Until the footing is broken out and the post is reset with a new embedment, any hinge you put on will wear out in a matter of months. We check the footing on every sagging gate call in Reseda. It is the first thing Hal looks at. Call (350) 247-4763 and we will tell you what is actually happening before we sell you anything.
Yes, and it is usually the heat acting on the steel frame, not the motor itself. Reseda routinely hits 105 degrees or higher in July and August. Iron and steel gates expand, bind against their stop bolts, and the motor has to push against that resistance. That burns out limit switches and circuit boards, then the motor. The fix is adjusting or relocating the stops, and sometimes reinforcing the frame so it expands evenly. The motor is often the victim, not the cause.
Yes. Even a brand-new gate installed with proper Gate Access Control in Reseda planning is typically being mounted to posts set in concrete that cracked in 1994 unless the footing was replaced. That is why we check every existing post and footing before we mount a new gate. If the concrete is cracked or the post rocks even slightly, we recommend replacing the footing and the post first. We do not install a new gate on a compromised base. That is how you end up with a multi-thousand-dollar gate that sags within the year. The quake is old news to a lot of people. To a gate contractor in Reseda, it is a daily reality.
Yes. Fall Santa Ana winds hit the interior Valley with sharp, sustained gusts that push lightweight aluminum and older iron slide gates hard against their guide rollers. The top rail bends, the gate jumps the track, or the guide posts shift. We see it every year, usually after the first strong event. The repair is usually bending the rail back, aligning the rollers, and checking the guide posts for movement. If the post moved, we are back to the footing conversation again. Call (350) 247-4763 and we will get it back on track.
Because in Reseda, a sagging gate and a cracked post-1994 footing go together more often than not. If the post rocks at the base or the concrete around it shows a radial crack pattern, the gate will re-sag within months of any hinge or latch adjustment. The footing has to be broken out and repoured before anything else will hold. Companies that skip that step are selling temporary fixes. We will not do that. Hal would rather tell you the truth and do the job once. That is why the 90-Day Done Right Promise is in writing.
Contact Gatewood Fence & Gate in Reseda
If your gate is sagging, off its track, or eating opener motors, call Hal at (350) 247-4763. You will get a live person on the phone, not a voicemail. We will schedule a time that works for you, show up when we say we will, and give you a written price before any work begins. Estimates are free. And if something is not right within 90 days of the job, Hal comes back. That is the promise. It has been the promise since 2001, and it is not changing.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving Reseda and the surrounding San Fernando Valley.