Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across North Hollywood
If your gate is sagging, jammed, or cracked, the fix usually comes down to the parts and the steel, not the whole gate. Gatewood Fence & Gate has been owner-operated since 2001, and our Gate Parts & Welding team welds on site so your gate stays in your driveway. In North Hollywood, where summer temps routinely cross 105°F, heat-stressed hinges and warped frames are the real culprits behind most gate failures we see. Call (350) 247-4763 and you’ll get a live person, not a recording.
Why Gatewood Fence & Gate Is North Hollywood’s Preferred Gate Parts & Welding Company
We’re not a franchise with a van that drives in from somewhere else. Hal Gatewood’s name is on the shop and on every invoice, and the person who answers your call is the same person who’ll show up. North Hollywood homeowners keep our number saved because we do the thing other companies skip: we repair the steel that’s actually failing. A gate sags in the hinge post, not in the middle, and that is where we start. We’ve fixed more sagging gates off Burbank Boulevard and Lankershim than we can count, and we know what happens when a North Hollywood Gate Motor & Opener from the 1980s finally cooks itself in July. We flag the electrical inspection issue before the city inspector does, because we’ve been through it with landlords all over the NoHo Arts District.
Every job we do in North Hollywood carries the 90-Day Done Right Promise in writing. If it’s not done right, one call brings Hal back. No fine print, no runaround. We also never charge a trip fee inside the county, and we’ll give you a free second opinion on any written estimate you’ve already got from another company. You don’t have to haggle with us. The price we quote is the price you pay, agreed before any work starts.
Our Gate Parts & Welding Services in North Hollywood
Hinge Replacement
Hinges fail first in this climate. The dry Valley heat expands steel, and when a gate’s hinge pins bind, the whole frame twists until something gives, usually the hinge itself or the weld holding it. We replace hinges in place, re-welding the brackets so the gate hangs true again. Fix the panel without the post and you’ll fix it twice. We do the hinge and the post in one visit.
Post Replacement
The post is the spine of any gate, and in North Hollywood’s older housing stock, those posts are often 40-year-old steel set in shallow concrete that’s cracked from decades of heat cycling. We dig out the failed footing, set a new post in deeper concrete, and re-weld the gate to it. On a wide drive gate, we’ll step up to a heavier wall post than what was originally there, because a gate that spans 14 feet in 110°F heat flexes more than the original installer ever planned for.
Rail Repair
Rails get bent, cracked, and rusted, especially on the rolling gates that front so many North Hollywood apartment carports. A bent rail makes the rollers fight every inch of travel until the motor burns out trying to push it. We straighten rails in place when we can, and when we can’t, we cut out the bad section and weld in new steel. The gate rolls like it should afterward, not like it’s dragging a flat tire.
Custom Welding
Not every repair is a standard part. When a wrought-iron pedestrian gate off Magnolia Boulevard getscracked at a decorative scroll, or a chain-link drive gate needs a new receiver bracket built from scratch, we fabricate it on the spot. Our Gate Parts & Welding work includes custom brackets, reinforcement plates, and rusted-through panel repairs. We weld with the gate still on its hinges whenever the job allows, so you’re not waiting a week for a shop to return it.
Gate Rollers
Rollers take the beating in North Hollywood. Hard municipal water leaves mineral scale on the rollers and tracks, and that grit chews up bearings fast. We replace worn rollers, clean and de-scale the track, and lube everything with a high-temperature grease that actually stays put in Valley heat. The difference in how the gate moves is immediate. If you’ve been listening to your gate grind every morning on Colfax, the rollers are almost certainly the noise.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in North Hollywood
We service and repair Gate Access Control - North Hollywood operators from FAAC, BFT, Linear, and Viking, among others. Hal is certified on nine major gate brands, which means we don’t have to puzzle through your opener with a manual in one hand. We keep common FAAC and Linear boards and limit switches on the truck, so a lot of North Hollywood repairs get finished the first visit. When a part isn’t in the truck, we know exactly where to source it and we’ll tell you the honest lead time before we touch anything.
Common Gate Parts & Welding Problems We See in North Hollywood Homes
- Circuit boards fried by Valley heat. An enclosed gate operator on a sun-baked driveway off Laurel Canyon can hit 140°F inside the housing on a 105°F day. Boards and capacitors don’t survive that forever. If your gate works at 7 a.m. and dies by noon, heat is the prime suspect.
- 1980s slide-gate motors wired into pre-arc-fault subpanels. When those originals finally fail from heat damage, replacing them can trigger a City of LA electrical inspection that landlords never see coming. We flag it before the work starts so permits don’t slow the job down.
- Warped steel frames from dry heat. North Hollywood gets 20 to 30 degrees hotter than Santa Monica. That expansion and contraction cycle bends frames, shifts alignment, and binds rollers or shears hinge pins. Straightening and re-welding the frame is a permanent fix; just replacing the roller is not.
- Mineral scale on hinges and rollers. The Valley’s municipal water is hard, and whatever overspray hits your gate eventually leaves white crust on every moving part. It accelerates wear dramatically. We see hinges that should last 15 years fail in five because they were never cleaned and lubricated.
Pricing for Gate Parts & Welding in North Hollywood, CA
A typical hinge replacement in North Hollywood runs $120 to $280 per hinge, depending on size and whether the bracket needs re-welding. Post replacement usually runs $450 to $900, with heavy steel driveway posts at the top end. Rail repair sits between $180 and $400, and custom welding is quoted by the hour, generally $95 to $140 per hour, plus materials. Full roller replacement on a rolling gate runs $200 to $500 including track cleaning. You’ll always get a written price before any work starts, agreed in advance. We don’t surprise you at the door. Call (350) 247-4763 for a free estimate, and remember: seniors and veterans get 10% off, every job, permanently. If a repair totals over $200, we take $40 off right there.
We Also Serve Cities Near North Hollywood
Gatewood Fence & Gate serves North Hollywood and the surrounding Valley communities, including Van Nuys, Sherman Oaks, West Hollywood, and Panorama City. If you’re just over the line, you still get the same live-person answer and the same 90-Day Done Right Promise. No trip charge inside the county, anywhere we go.
Serving North Hollywood, CA - Our Local Coverage Area
We’re based in the North Hollywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in North Hollywood
It depends on the electrical work involved. When one of those original 1980s slide-gate motors is replaced and the wiring runs back to a pre-arc-fault subpanel, the City of LA often requires updated circuit protection as part of the permit approval. That means the electrical portion, not just the operator swap, becomes part of the job. We flag this before quoting so nobody gets a stop-work order or a surprise inspection. Call (350) 247-4763 and we’ll tell you what your specific carport is likely to trigger.
Because the hinges were probably replaced without addressing the post. When the post is cracked, set shallow, or leaning, new hinges just transfer the load to a foundation that’s already failing. The gate then sags again within months, especially through a Valley summer when the steel expands daily. Our rule is simple: fix the panel without the post and you’ll fix it twice. We check the post’s footing with a level and a pry bar before we ever weld a new hinge on.
We weld on site, in your driveway, with the gate still hung whenever the crack allows access. We bring a mobile welding rig and the work is done that day in most cases. Only when a frame is twisted beyond what clamping can correct do we recommend removing it, and even then we won’t haul it to a shop. We straighten and weld it on a flat surface in your yard or driveway. The gate never leaves your property.
A solar gate opener with battery backup is the answer for a long driveway where running mains power isn’t practical. We installed one off Victory Boulevard on a property where the driveway ran 300 feet from the house; trenching and conduit would have cost more than the operator itself. The solar panel keeps the battery charged, and the battery powers the motor through cloudy stretches and night cycles. On heavy or wide gates, we spec an operator with enough duty rating for the gate’s weight and span, not just whatever the box says at the hardware store. Call (350) 247-4763 and we’ll size it correctly for your gate, not the other way around.
Every three to four months, minimum. North Hollywood’s municipal water leaves mineral scale on hinges, rollers, and lock mechanisms, and that scale acts like sandpaper once it builds up. Coastal homes can get away with twice a year; Valley homes cannot. We use a high-temperature grease that holds up in 105°F heat rather than thinning out and dripping off. If your gate is already grinding, lubrication won’t fix it; the rollers or hinges need to be replaced first, then maintained. Call us for a free estimate and we’ll tell you exactly what it needs.
Contact Gatewood Fence & Gate in North Hollywood
When your gate stops working, you want a person who answers, a price that sticks, and a fix that lasts. That’s what we do. Hal Gatewood has been doing this since 2001, and the shop isn’t some call center three states away. It’s a local business with a published address and a license number you can look up. Show me the gate closing on its own and I’ll show you where it’s failing. Call (350) 247-4763 for a free estimate on any Gate Installation in North Hollywood, gate parts, or welding work. We’ll give you a straight price before any work begins, and we’ll stand behind it in writing for 90 days.
Written by Hal Gatewood, Owner at Gatewood Fence & Gate, serving North Hollywood since 2001.